山東通風管道加工按材質分： 一般有：鋼板風管(普通鋼板)、鍍鋅板(白鐵)風管、不銹鋼通風管、玻璃鋼通風管、塑料通風管、復合材料通風管、彩鋼夾心保溫板通風管、涂膠布通風管(如礦用風筒)、礦用塑料通風管等，近出現了一種新型管道，使其作用更加多樣化。

　　Ventilation pipe material: General: steel duct (steel), galvanized plate (Bai Tie) wind pipe, stainless steel pipe, glass steel ventilation ventilation pipe, plastic pipe, composite pipe ventilation ventilation, ventilation pipe, sandwich insulation board rubberized cloth ventilation tube (such as mine, mine ventilation duct) plastic pipe so, the recent emergence of a new pipeline, making it more diversified.

　　1、 風管加工過程會產生粉塵或纖維飛揚，現場切割風管人員必須佩戴專用的防塵眼罩及口罩操作，防止切割時產生的粉塵吸入體內。

　　1, the wind pipe processing process will produce dust or fiber flying, on-site cutting wind pipe personnel must wear special dust goggles and mask operation, to prevent cutting dust generated by inhalation.

　　2、當風道與除塵設備、加熱設備等銜接前，應待設備裝置終了后，按理論測繪的圖紙中止預制和裝置。

　　2, when the air duct and dust removal equipment, heating equipment, etc., before the equipment should be completed, according to the drawings of theoretical drawings to stop the prefabrication and installation.

　　3、當天施工結束后的剩余材料及工具應及時入庫，不許隨意放置。

　　3. The remaining materials and tools after the day's construction shall be put in storage in time, and shall not be allowed to be placed at will.

　　4、濟南通風管道裝置時，進、出風日宜在風道預制時開出洞口，如需在裝置終了的風道上現開風口，其接口處應緊密。

　　4, Ji'nan ventilation pipeline device, in and out of the open hole in the air duct should be prefabricated, such as in the end of the air duct device on open air, the interface should be close.

　　5、風管加工中使用的氧化鎂，氯化鎂應妥善存放，注意防火且不得直接在陽光下曝曬。失效的氧化鎂，氯化鎂及原料包裝容器不得隨意拋棄或燃燒，應集中堆放處理。

　　5. The Magnesium Oxide and magnesium chloride used in the processing of air duct should be stored properly, and attention shall be paid to fire prevention and shall not be exposed directly to the sun. Failure of Magnesium Oxide, magnesium chloride and raw materials packaging containers shall not be discarded or burned at random, should be concentrated stacking treatment.

　　6、當運送含凝結水或含濕量較大的氣體時，其水平管道宜設有坡度，并在低點處接排水管。裝置時風道底部不宜呈現縱向接縫，對底部有接縫處應中止密封處置。

　　6, when carrying water containing condensate or more humid gas, the horizontal pipe should be equipped with a slope, and at the low point to connect the drain pipe. When installing, the bottom of the air duct shall not be longitudinal joint, and the sealing joint shall be stopped at the seam at the bottom.

　　6、施工時需要照明亮度大和噪聲大的工作盡量安排在白天進行，減少夜間施工照明電能的消耗和對周圍居民的影響。

　　6, the construction needs illumination, brightness and noise work, as far as possible in the daytime arrangements, to reduce the night construction, lighting, electricity consumption and the impact on the surrounding residents.

　　7、現場制作通風管道時，在切割平臺1～2 米處設置專用風扇或風機，將切割時產生的粉塵吹向通風相對良好的開闊區(qū)域，減少粉塵被制作人員的吸入及對視線的影響。

　　The ventilation pipe 7, making the scene, in the cutting platform 1 ~ 2 meters set up a dedicated fan or blower, dust will be generated during the cutting blow to the open area relatively good ventilation, reduce dust by inhalation of production staff and the impact on the line of sight.

　　本文的精彩內容來自山東通風管道加工詳細內容請點擊我們的網站:http://norcalcrt.org/謝謝您的到來!

　　The highlights of this article are from the Shandong ventilation pipe processing details, please click on our official website: http://norcalcrt.org/, thank you for coming!

上一篇：空調風機盤管清潔的優(yōu)點
下一篇：風管穿越沉降縫時的注意事項